Topic: Maybe new Cure for MSI K7N2 Delta 2 LSR/Platinum Owners (Read 223545 times)

Svet · « **on:** 05-August-05, 08:06:39 »

BOSSKILLER: Modded BIOS Use At your own Risk!

Based on unofficial original MSI B61 version
Supported motherboards:
MSI K7N2 Delta 2 LSR
Compatible also with MSI K7N2 Delta 2 Platinum (can be used also)

filename:
W6570NMS.B62 - IMAGE BIOS
readme.txt - This file
flash.bat - batch file (use this to automatic flash when you boot under clean DOS)
AWFL833C.EXE - AWARD/MSI flash Utility

Fixes and Changes:
Improved stability by 90%
Abjucted Alpha timming and latency for better perfomance
Added Temperature Shutdown options
Added FSB on the Fly to be Visible
Added DDR400 Patch to be Visible
Added USB Park Mode options
Added USB Read Requests From options
Added USB Perfomance Mode options
Added Media Interface options
Added MAC(NV) options
Added NV/ATI Speed Up options
Added PCI Clock Auto Detect options
Added Support for Mobile Barton and fix to be Detected Property by OS
Fixed holding "INS" key during powerup to reset CMOS settings to deafault
Fixed bug when using both keyboard and mouse USB in same time in XP cause to
loosing USB mouse on reboot.
Fixed Temp Sensor bug which cause temperature to cut down imediatly by 10-15C after stop stress test.

Known and remaining bugs:
Incompatible with Corsair Twinx CAS 2 Series in Dual Mode
S3 Power Managment cause machine to lockdown when using SleepMode after trying to wakeup.
Lockdown also when using Hibernate. S1 Power Managment no problem reported.
Frooze in Prime 95 almost imeediatly or cause Blue SOD of short period of time when using
settings differents than this in Cell Menu: High Perfomance Mode: Optimised. Dynamic Overclocking must be enabled obligatory to Private or Sergeant when you using non Optimised settings.(etc. when you try to set settings manual)
Problem with Multipler 9.5 and 10 when FSB is set to over 200Mhz PC wont post and froze at
"BIOS Decompression Error". if you use over 200FSB avoid 9.5 and 10 Multipler.

Recommend settings in Cell Menu:
High Perfomance Mode: Manual
Dynamic Overclocking: Private(1%) or Sergeant(3%) (gives automaticly boost in percent to CPU,FSB,AGP Card when CPU reach 100% usage.when activity is lowered for 3-4secs gain normal state)
CPU Interface: Optimal - gives best results in memory read. also some video card like Galaxy 6600GT gives problems(frooze, lockup PC when this setting is set to Aggresive)
NV/ATI Speed UP: Auto
Adjust DRAM Freq(FSB:DRAM): 1:1
FSB Spread Spread Spectrum: Disable (available on 100,166,200 FSB)
AGP Spread Spread Spectrum: Disable (available on 100,166,200 FSB)
Adjust AGP Frequency: Manual
-AGP Clock Value: 66
All other settings configure as you like depending of hardware that you have.

Which have interest to PM me will send BIOS via e-mail.

Niksoftware · « **Reply #1 on:** 11-August-05, 21:28:40 »

Does this solve the CAS being stuck @ 2 ?

For more details:
http://forum-en.msi.com/index.php?topic=85097.0

Svet · « **Reply #2 on:** 11-August-05, 23:27:41 »

didnt find any probs to set any memory timming which i want. all work correcctly. but nede to folow some recoomended setings in readme also.

about this in your post link:
"This problem is infuriating me coz i have had to replave valueselect 2x512mb corsair ram with ocz platinum el 2x512mb because the cas for the corsair had to be 3 but the ocz is 2-2-2-5"
Curently i use 2x256 Twinx Corsair no prob to set 2-2-2-x(in my case 10) all work corectly with impresive perfomance. passed all stress tests

CPU is Mobil Barton 2400+

Jeff ET · « **Reply #3 on:** 12-August-05, 10:30:38 »

hi i wanna info about your bios because b5 are so unstable i cant put ratio to 1:1

Svet · « **Reply #4 on:** 12-August-05, 14:52:31 »

hello. what more info want? i've tested 2x512 knigston value ram 3200 3.0,3,3,8 and with kingston value Dual KIT didt find any probs. reached without problems 218FSB - rock solied stable FSB(1:1 of course). make sure that you have not malfuction RAM. test it one bank 1st alone then other bank alone. use memtest for beggining. select test N5 make sure to pass 10-12 times without error.

Jeff ET · « **Reply #5 on:** 12-August-05, 17:57:34 »

my ram are brand new (since 2 week ) and already run stable whit bios B3 (and ratio 1:1) but i broke me floppy drive than i cant go back to bios B3.... i think are better to go buy another one

Svet · « **Reply #6 on:** 12-August-05, 18:03:10 »

there is other way to update BIOS using dedicated partition or boot from alternative CD-ROM or Flash RAM.
so your comp is fine with B3 but with B5 you got problems right?

Jeff ET · « **Reply #7 on:** 13-August-05, 18:03:04 »

yes that right whit b5 its impossible to doing overclock or just changing setting ... but whit b3 that fine ,,,,,when i RMA my board they update my bios but i go buy floppy driver today

Niksoftware · « **Reply #8 on:** 13-August-05, 18:08:38 »

Added FSB on the Fly to be Visible
Added DDR400 Patch to be Visible

What do these actually do? esp ddr400patch?

and can you confirm you need dot on at least private to be stable even when trying to overclock fsb>200?

DaveR · « **Reply #9 on:** 13-August-05, 18:40:48 »

Bosskiller told me before; "DDR 400 patch must be set to Disable. if it is Enabled (that's is by default) gives legion of memory errors of all kind of memory. Disable this setting fix memory errors".

As for fsb on fly; when you change fsb in bios you can't see the change until you save and reboot; I think this patch makes it visible immediately.

Niksoftware · « **Reply #10 on:** 13-August-05, 21:07:26 »

What about auto overclock at private setting?

should i have dot on at1% even when im trying to test 200/220+ fsb's?

Jeff ET · « **Reply #11 on:** 13-August-05, 23:29:42 »

Quote from: Niksoftware on 13-August-05, 21:07:26

What about auto overclock at private setting?

should i have dot on at1% even when im trying to test 200/220+ fsb's?

i dont trust that i prefer to set my own overclocking setting

Niksoftware · « **Reply #12 on:** 14-August-05, 17:21:15 »

Can you tell me what questions i must ask myself to find out if i want to go from b5 to b62?

And can you shed any light on: in what way it is more stable other than being able to disable ddr400 patch?

I take it the word is disable ddr400 patch?

I have already accessed the extra options with shift+f2 and alt+f3 so what more stability would i gain?

And i would like bosskiller's own opinion if i am tryinf for 220+fsb's should i really have DOT @ 1 or 3%?

Svet · « **Reply #13 on:** 14-August-05, 17:31:58 »

i just PM to you.
DDR400 Patch is modded ROM Strip table
DOT must be enable for safest and 1% (Private)
other questing i descriped in PM to you. have to go now. pm me how its going

Regards

Jeff ET · « **Reply #14 on:** 15-August-05, 06:19:45 »

where i can find bios B6.1

gratis · « **Reply #15 on:** 17-August-05, 17:28:51 »

Quote from: BOSSKILLER on 05-August-05, 08:06:39

Fixed holding "INS" key during powerup to reset CMOS settings to deafault.

Bleh!

What versions of BIOS was that broken in?

I am/was looking to flash up my bios after my system is stable (see whole other tread in Motherboard area)

What bios should I be aiming for (greatest stablity with few-no bugs) Should I just stay at baseline??

Svet · « **Reply #16 on:** 17-August-05, 17:43:07 »

in all prevision exept B30 (for B72 dunno when i have time will see whats changes). not working at all the time. sometimes work sometimes not. if your system is stable. better keep it. dont flash with other.

gratis · « **Reply #17 on:** 17-August-05, 18:06:20 »

Is there somewhere were I can find the BIOS release versions and Actual notes on what the fix and know bugs?
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=613&kind=1

Is TOTALLY lacking in details...

DnL · « **Reply #18 on:** 13-September-05, 05:51:24 »

ok using B62 now and running prime95

So far great, right now cpu at 12x202 mhz @ 1.75v and DDR @ CAS 2.5-3-3-8 - 2.7v

Question: Is the CPU temp reading +10 instead of normal? Cause using external probe it says 46-47c, while on MSI CoreCenter reads 58c?

Touched the heatsink near the cpu almost feels warm, but not enough for 58c

Any feedback guys?

Svet · « **Reply #19 on:** 13-September-05, 06:25:19 »

temp reading is fine.
use speedfan for most actual results.
curently using Mobil Bartona 2400+
running at 11.5x205 = 2357Mhz at 1.825Vcore full load max temp 56C using ThermalTake Volcano 12

DnL · « **Reply #20 on:** 13-September-05, 07:32:23 »

stills marks high 58c runing prime, but doesnt "feel" like 58c

B3 temp was 46-47c under prime, well i can live with that ;P

great 4 hr of prime and 0 error

Sagia · « **Reply #21 on:** 13-September-05, 17:42:43 »

How you mod the bios? Can you share it with us and if possible I want you to make moded b.3 bios.

Svet · « **Reply #22 on:** 12-October-05, 14:40:18 »

got a latest fresh copy of B.71b MSI original still Beta version. will investigate in a next week.now i have to celebrate got a birthday today.

Wonkanoby · « **Reply #23 on:** 12-October-05, 14:47:42 »

Grayone · « **Reply #24 on:** 12-October-05, 18:49:48 »

Happy Birthday, Bosskiller

Enjoy each and every one.

ols · « **Reply #25 on:** 15-October-05, 13:49:47 »

Hi Bosskiller,

does your mod add the missing CPU multilier in the Cell menu?

My problem is the following:
I'm using an Athlon XP Barton 2800, FSB 266 with multiplier 16x (device number "AXDA 2800 DKV4C").
Now I want to run this CPU with a multiplier of 13x or 14x, but these are not available in the bios. I tried
several multis and what I get is that 7x behaves like 15x and 7.5x like 15.5x and so on. (as it is seen in the
table on this page http://fab51.com/cpu/barton/athlon-e20.html)

It seems that only the lower half of multipliers is implemented in the original bios.
So I need the missing multipliers 5x and 6x from the lower half (that should result in 13x and 14x).

Regards
ols

Peter Bacon · « **Reply #26 on:** 19-October-05, 11:56:40 »

Hello BOSSKILLER,
Could you send me your last bios (B62 or B71).
Thank you

Svet · « **Reply #27 on:** 20-October-05, 11:24:15 »

Quote from: ols on 15-October-05, 13:49:47

Hi Bosskiller,

does your mod add the missing CPU multilier in the Cell menu?

My problem is the following:
I'm using an Athlon XP Barton 2800, FSB 266 with multiplier 16x (device number "AXDA 2800 DKV4C").
Now I want to run this CPU with a multiplier of 13x or 14x, but these are not available in the bios. I tried
several multis and what I get is that 7x behaves like 15x and 7.5x like 15.5x and so on. (as it is seen in the
table on this page http://fab51.com/cpu/barton/athlon-e20.html)

It seems that only the lower half of multipliers is implemented in the original bios.
So I need the missing multipliers 5x and 6x from the lower half (that should result in 13x and 14x).

Regards
ols

hmm well.. maybe CPU is locked? multipliers is aveilable in cell menu 13x,13.5.
if CPU cannot run on this multiplers too much Mhz or CPU is locked.
there is no changes in multipliers in BIOS based to original. but multipliers is there.

Svet · « **Reply #28 on:** 20-October-05, 11:24:43 »

Quote from: Peter Bacon on 19-October-05, 11:56:40

Hello BOSSKILLER,
Could you send me your last bios (B62 or B71).
Thank you

done..

Svet · « **Reply #29 on:** 20-October-05, 11:27:09 »

thank you Wonkanoby

thank you Grayone

Peter Bacon · « **Reply #30 on:** 20-October-05, 17:56:15 »

Thank you BOSSKILLER !

Faxydre · « **Reply #31 on:** 20-October-05, 21:18:36 »

yea GREATS THANKS BOSSKILLER, your 62 bios fixed 90% of my system bugs

Can you tell us more about 71 bios (and maybe 72 BK bios

are there more fix ?

Svet · « **Reply #32 on:** 20-October-05, 22:20:05 »

Quote from: Faxydre on 20-October-05, 21:18:36

yea GREATS THANKS BOSSKILLER, your 62 bios fixed 90% of my system bugs
Can you tell us more about 71 bios (and maybe 72 BK bios are there more fix ?

no answers for now m8. i dont have a time to investigate B.71 for now.

ols · « **Reply #33 on:** 21-October-05, 17:37:28 »

Quote from: BOSSKILLER on 20-October-05, 11:24:15

hmm well.. maybe CPU is locked? multipliers is aveilable in cell menu 13x,13.5.
if CPU cannot run on this multiplers too much Mhz or CPU is locked.
there is no changes in multipliers in BIOS based to original. but multipliers is there.

No, the CPU is not locked. The standard multiplier is 16x and I can switch to 15x ot 17x
by choosing 7x or 9x in the Cell menu.
There are 5 bits determining the multiplier and I think that the highest bit is always set to 0.
This would mean that I cannot use 13x from Cell menu, but I have to use 5x and 6x that
should result in 13x and 14x.

ols

moguail · « **Reply #34 on:** 21-October-05, 19:00:07 »

Hello BOSSKILLER,
Could you send me your last bios (B62 or B71 or B71 ??).
Thank you

TheCyberDude · « **Reply #35 on:** 25-October-05, 04:15:27 »

BOSSKILLER,

Could you send me the B62(Modded) AND B71 BIOS's for MSI K7N2-Delta2-LSR ?

gwinkle@juno.com

Thank You,
TheCyberDude

Thank's BOSSKILLER, for Sending BIOS's !

Svet · « **Reply #36 on:** 25-October-05, 11:23:30 »

done..

andrea20ge · « **Reply #37 on:** 25-October-05, 13:34:23 »

Quote from: BOSSKILLER on 25-October-05, 11:23:30

done..

hi i'm Andrea....and i need a mod bios for the k7n2 delta 2 fsr...
your bios is wrong? sorry for my bad english but, i'm a italian boy.
can u sandme it?
pandaztc@hotmail.com
tnku1000!

another answer :D
why with a asus k7n8x-x i can select the multiplicator of the cpu but with this mobo i dont do it..?
i use a 2600 thoro b tested stable at 2300mhz... when i select 10x multi 200fsb the mobo don't boot..
when i select multi 10X fsb default at 266 (133) the mobo don't boot.
i test the b.4 and b.5 bios but...i dont resolve the questions...

sorry for this but the overclock is most important for me :D

in past i have the k7n2 delta 2 lsr...but it burned... :D

andrea20ge · « **Reply #38 on:** 26-October-05, 13:07:51 »

the bios boot!!!
great !
but i have a problem...
i have all multiplicator @2x
for example... 8x=16x
10x=20x
7x=14x
can u helpme?

josejak · « **Reply #39 on:** 31-October-05, 02:55:47 »

hi,sorry for my english; but i think the problem with this mobo is the "row cycle time" when i change the option in bios "high perfomance mode" to manual only that, the row cycle time change to 10 and the value in optimized is 11 and the other options renains without changes, thats is normal? i think is the problem.

Svet · « **Reply #40 on:** 01-November-05, 13:41:38 »

not big differents between B61 and B71. only few changes that's isnt important. MSI is trying to make stable this board by sacrifice the performance of mobo. few timmings are increased for better stability. not any changes in general.

if some one wana test it let me know.

http://show.bosskiller.fbi-most-wanted.us/

kamelot · « **Reply #41 on:** 02-November-05, 15:52:26 »

Hello BOSSKILLER!

Can you send me the modded B.62 and beta B.71 files, please. Thank you.

kamelot@dir.bg

Svet · « **Reply #42 on:** 02-November-05, 17:28:51 »

The server was not able to deliver your mail message to the following addresses:
kamelot@dir.bg
mail.dir.bg: domain name is too long
This is just a temporary error. The server will continue to attempt to deliver
the message. If the message cannot be delivered in the defined time limit you will
be informed again.
SMTP Send: 1 outgoing message processed in MX queue run

Give other e-mail address.

kamelot · « **Reply #43 on:** 03-November-05, 09:03:42 »

neverboy@abv.bg

Thank you.

Svet · « **Reply #44 on:** 03-November-05, 10:56:13 »

done... good to see another

here

Enjoy!

ratters · « **Reply #45 on:** 03-November-05, 17:36:15 »

Hi

Id like a bit of advise as to why my Tztec pc3200/400 2x1gb sticks fail to boot on my board but will boot on an older KT4v no probs

All are brand new and as yet no OC has taken place, power comes on but d bracket hangs on "memory" and blank screen.

Any advice would be very helpfull as ive had to switch to 2x512 pc2700/333 and the reason i bought the board was to use 400!!!

Am i missing something simple?

Rgds

Ratters

Burn2 · « **Reply #46 on:** 04-November-05, 13:18:12 »

Hello all, i am french so sorry for my futur mistake.
I had tried the bios b6.2 from bosskiller and i thing that it is quite good. Only one things, is it possible to had this vcore in the bios?
1.9v, 1.925 , 1.95v, 1.975v ?? Thank you very much, (i have got an msi k7n2 delta2 platinum mother board)
Thank you for this bios

Parseval · « **Reply #47 on:** 06-November-05, 00:58:14 »

Hi all,
I just bought new MSI K7N2 Platinum board to replace my old Soltek KT133 mobo. Unfortunately new board isnt very stable with Geil value RAM. Although I can boot to win without any problems, Prime gives me an error right after few seconds run. After reading this thread I have new hope to solve this issue. Bosskiller, can you send me your modified bios?

GunaySOFT · « **Reply #48 on:** 06-November-05, 11:50:10 »

Hi Everybody from Türkiye!!!

Is your modded BIOS fully stable?

I always think two times before doing these kind of mod....
Now using Official B5 bios and I think it is not stable...

Stability is more important than performance for me...

If you think it is better to use your bios for more stable world, just send me your bios's latest version...

Thank You BOSSKILLER!!!

Burn2 · « **Reply #49 on:** 06-November-05, 15:19:34 »

I think that the bios B6.2 made by bosskiller is better, juste one think, did you turn on the dot on 1% ? beacause this motherboard is not ok without dot enable when you are in manuel, the pc freeze and reboot whithout.

News:

Author Topic: Maybe new Cure for MSI K7N2 Delta 2 LSR/Platinum Owners (Read 223545 times)

Jeff ET

Jeff ET

Jeff ET

Jeff ET

Jeff ET

gratis

gratis

DnL

DnL

ols

Peter Bacon

Peter Bacon

Faxydre

ols

moguail

andrea20ge

andrea20ge

ratters

Parseval

GunaySOFT