B660M Mortar Wifi DDR4 Bios Cpu SA Voltage problem

J

jsoxj123d029a

New member
Joined
Jan 8, 2022
Messages
3
During RAM overclock, it was impossible to boot more than 3600 gear 1 setting, so I tried to adjust the options one by one and found them.
Even if the cpussavoltage value is changed, it does not apply.
It is not possible in all bios versions (100, 110, 122).I don't know if it's a bug or a problem with my main board, so I want to hear your experience. This is the picture when the sa voltage was set to 1.200.
View attachment 155451
 
SHALALA

SHALALA

Member
FIRST LIEUTENANT
Joined
Jun 19, 2017
Messages
514
jsoxj123d029a said:
During RAM overclock, it was impossible to boot more than 3600 gear 1 setting, so I tried to adjust the options one by one and found them.
Even if the cpussavoltage value is changed, it does not apply.
It is not possible in all bios versions (100, 110, 122).I don't know if it's a bug or a problem with my main board, so I want to hear your experience. This is the picture when the sa voltage was set to 1.200.
View attachment 155451
Click to expand...
Can you attached the screenshot again? Which RAM are you using?
After setting SA voltage, did you press F10 save then exit?
When you go back to BIOS, is there any error message? SA is still showing under 1.0V?
 
L

ligs8154b02da

New member
Joined
Jan 12, 2022
Messages
5
SHALALA said:
Can you also provide screenshot in BIOS? What will happen if you enable XMP? And what will happen if you set SA voltage higher than 1.0V?
Click to expand...
BSOD.jpg
If XMP is enabled, System will Crash soon...

BIOS.jpgAIDA64.jpg
Set SA voltage to 1.2v (Override Mode), Press F10 to save and reboot.
nothing happens... the SA voltage is still 0.92v...

RAM Model : BL16G36C16U4BL.M16FE1 (Crucial Ballistix DDR4 3600c16 16GB*2)
 
Last edited:
teletubby_po

teletubby_po

To infinity and beyond.
FIRST LIEUTENANT
Joined
Apr 6, 2020
Messages
1,991
jsoxj123d029a said:
During RAM overclock, it was impossible to boot more than 3600 gear 1 setting, so I tried to adjust the options one by one and found them.
Click to expand...
do you have issue with Gear 2 3600MHz? and can you list out your system spec in detail please? CPU and RAM sticker included
 
SHALALA

SHALALA

Member
FIRST LIEUTENANT
Joined
Jun 19, 2017
Messages
514
SHALALA

SHALALA

Member
FIRST LIEUTENANT
Joined
Jun 19, 2017
Messages
514
L

ligs8154b02da

New member
Joined
Jan 12, 2022
Messages
5
SHALALA said:
How about default settings with only XMP enabled? Don't adjust SA voltage?
Click to expand...
Case1: only XMP enabled, others settings are default = BSOD:shocked:
Case2: XMP enabled, set SA voltage to 1.2v = BSOD:shocked:
Case3: All settings default (RAM:2666Mhz), OK(y)
 
J

jsoxj123d029a

New member
Joined
Jan 8, 2022
Messages
3
SHALALA said:
Please use default settings and modify SA voltage, if it still cannot be adjusted, please remove AC power and clear CMOS then check again.
Click to expand...
There seems to be a problem with the Intel non-k processor now. When 12700k and b660 mortar are combined, sa is applied normally.
The sa voltage was not adjusted in the combination of 12700f and z690.
 
D

DXDT

DXDT
Joined
Jan 26, 2022
Messages
2
Same config and issue. Can we set to 3200 gear 1, is it better than 3600 gear 2?
 
Last edited:
Top