Big Bang XPower - OCZ Revodrive 120 gb SSD incompatiblity

malagi

New member
CORPORAL
Joined
Sep 22, 2010
Messages
13
Recently i bought a OCZ Revodrive 120gb SSD. Installed it on the right way and windows runned on it for a few minutes.

Only after a few minutes the first BSOD occured and it keep on rebooting every few minutes after a reboot.

Is This a know problem of incompatiblity beteen the 2? Also, Windows runs without a problem in safe mode.
And also if i install the Revodrive in an existing windows install on an other harddrive i can acces the harddisk without any problem.
So it seems to be a driver/windows service bug or error.

Maybe others here have the same problem.

BIg bang Xpower motherboard
Core i7 950
Corsair XMS3 DDR 3 1333 2x2gig
Club3D HD 4870 1 gb
Coolermaster silent pro 1000
OCZ Revodrive 120
2xWD Green caviar 1.5tb
Windows 7 home premium X64
 
After much screwing around i finally got the revodrive 120gig pci-e ssd drive to work with my Big Bang, turns out the pci express default power management settings in windows 7 (using 64 bit here) is set to moderate, the pci-e power poll calls to the revo were causing WHET pci express root bus errors till it bluescreened. Went into safe mode and turned to performance settings, or if you wish, advanced settings, pci express then disable, now works great ;) As a stop gap to get windows to finish installing, go into safemode, hit Shift F10, run services.msc, disable the power service, once windows is finished installing, re-enable the power service, reboot into safe mode, change above settings ( i did in safe mode so it wouldn't reset on me) Hope it helps, i spent many hours getting this drive to work for my customer, hope it saves you the aggravation or gives a clue to a bios update to make this card\SSD drive work right

Denis Boisvert @ Cyber Solutions
 
In regards to OCZ Revo issue with Xpower, here is the latest beta BIOS for you to try.

Big Bang Xpower 7666 BIOS v1.47

Sincerely,
Warner
 

Attachments

Warner said:
In regards to OCZ Revo issue with Xpower, here is the latest beta BIOS for you to try.

Big Bang Xpower 7666 BIOS v1.47

Sincerely,
Warner
Anyone have any luck with the Revo and this BIOS? Where can I get the BIOS to try...I'm getting BSOD with the RevoDrive X2 on Windows load. I'm going to try the power tip above but I think I already have that set that way.
 
It's attached above, see above. You can't see attachments until you are log-in with your account.
 
Svet said:
It's attached above, see above. You can't see attachments until you are log-in with your account.
DOH! :bonk: I never looked back after I registered, thanks. I also spotted the beta-BIOS thread.

I will report back as to whether or not this remedies the BSOD with the Revos. I have a RevoDrive & RevoDrive X2 in my possession and will check both.

 
The new BIOS seems to have done the trick.:agrees: I am able to boot with the RevoDrive X2 installed (not as the OS drive) without errors or BSOD. I'm imaging my OS to it and if I have issues booting from it, I'll post an update. Otherwise, it should be good to go.
 
Scuba said:
The new BIOS seems to have done the trick.:agrees: I am able to boot with the RevoDrive X2 installed (not as the OS drive) without errors or BSOD. I'm imaging my OS to it and if I have issues booting from it, I'll post an update. Otherwise, it should be good to go.
Imaged the OS onto the rive and the BIOS will not recognize it at all as a boot device :think: Regardless of what is or isn't on the drive, It doesn't do the normal load pre-windows as shown HERE.

***EDIT*** Found the problem. the "Onboard E-SATA Controller" setting int he BIOS must be set to IDE or Disabled. The BIOS now recognizes the drive in the list of available drives. Windows boots fine!
 
Are there any known issues with the 1.47 beta BIOS (that you can share) at this time that we could look out for?
 
The posts above were very helpful in my installation of the RevoDrive X2 160GB on my Big Bang as my primary hard drive so I wanted to post a detailed response on how I got the operating system installed on it and my theory on what could be possible issues with accomplishing that goal for some users. I wont give you a bunch of BS about bench testing and all that but just some useful data in executing this specific install. That said, starting small and building up will save you some time. This might seem long but I have been so frustrated with not being able to find enough detail to help me out so I wanted to make sure this is out there to help people out.

I am using an Intel i7-980x, Big Bang XPower MB, Kingston 2GB 3DDR 1600 RAM (I have 6 but dont stick em all in to start with), 1000wt Power Supply, 2 ATI 5770s, 1 USB 3.0 PCI, MB audio card, Cool Master X case and a RevoDrive X2 160GB. I am listing the specifics in an effort to assist others who might be trying to drill down on the problem. I am using Windows 7 professional 64 bit and am using the unit for business purposes on a network that houses most of the large data. The purpose of the install was to increase capacity of the workstation and reduce the bottleneck of having the operating system on a standard hard drive. If you are trying to install this in an effort to do gaming and need to have multiple hard drives this probably isn't for you. In testing the device I have found that maximum efficiencies are only found when having the operating system and all programs installed on one local hard drive.

The key is in setting up the Bios to disable all items with RAID or SATA in the description. This includes disabling ALL such items. Then, with only 2 sticks of ram, 1 graphics card and a maximum power supply of 1000 install Windows to the drive. I would use a USB installs rather than a CD for the drivers and operating system. I used a CD for windows and a USB for the Revo driver but wouldn't do this approach if I was doing it again. DO NOT connect any other hard drives via SATA or attempt to install any MB programs involving RAID...this will hose the process. I would also  pull out the MB battery and flip it over and stick it back in to shot it out. Then flip it back prior to install.(This is the small hearing aide looking battery which is located on the MotherBoard right near the PCI-E slots.) Make sure you don't have it plugged in when you do this.

Install Windows. When you get to the install you will need to manually install the hard drive driver from USB. Make sure you install the driver and then flip it back to the operating system disk if you are using an all CD approach. If you don't flip it back to the operating system disk after installing the disk driver you will get an error. I would also pull out the disk or USB following the install of the hard drive driver before moving forward to insure you don't get a windows error. Be aware that you wont see the drive going into the install. You have to go into it blind...you will basically identify the drive for the PC by installing the driver during the operating system install. Once you install the driver, remove the disk, put the operating system disk back, then refresh and then hit next you will be able to move forward. You will then push it forward just in an effort to get just a basic install in place. You will likely get errors and blue screens, Just try to get a setup user in place. Once just this is done you will shut down the workstation. Then pull the card out, reshort the MB and stick the card back. Restart and then fire the unit back up. You will have to get the install 100% in order to shut it down again so you can enter it safe mode. Once you do then set your profile for maximum performance in your power profile, double check that there are no PCI power or data limiting settings and then insure that you don't have disk fragmenting set up to run on the drive. Then run windows update first thing before any other programs. Then go to MSI and install the drivers but make sure you don't install any RAID or SATA drivers. You don't want anything with RAID or SATA introduced to the MB/workstation. Install each program one by one...testing as you go. I don't know for sure what would or wouldn't hose the system but found problems when trying to incorporate any SATA based devices. I eventually nixed out even the CD drive and replaced it with a USB based drive. I also found problems with a power supply over 1000, in migrating over a HD from a previous SSD, in trying to incorporate an existing RAID profile or in trying to base the operating system on a separate SSD. You can do this but you will likely get blue screens and reduced efficiencies. The true benefit of the drive is found when everything is on it. If you need to have more than 160GB of local data I would get a larger drive but not trying to rig it with an existing SSD or other HD. I also found issues when trying to shove the MB full of RAM. I would just use 1 or 2 sticks and then load it up later. I haven't found the chance yet to push the limit on that but think once you have the OS on the drive with the programs that you wont have as much need to focus on the RAM.

I also didn't find luck with using the last slot on the board. If you went to the cost of the Big Bang MB and the RevoDrive then you likely are trying to use something along the lines of a ATI 5770. I have 2. Since they are doublewides I tried the card in PCI 4 so I could have the audio in 1, the ACI in 2 (hanging over 3), the card in 4, the second ATI in 5 (hanging over 6) and then the USB 3.o in 7. This fits with the MB instructions on running a crossfire setup and also is the only configuration I found that works through setup and after the install of the OS and programs. If you are trying to run the OS on this just don't install a RAID driver or anything connected via SATA. Just buy a USB CD/DVD drive and if you need more storage get a larger Revo. If you do you will be shocked by the performance. Most of those that have found fault in the device that I have seen are trying to use it with the OS installed on a separate SSD. This defeats the purpose of the Revo.

I hope this helps those that read this! I wish I would have had this detail before I started to avoid the past 2 days of agony! The postings from scuba were very helpful in my install and hopefully these extras with help those that read this! The process is very frustrating and the drive is very sensitive to any programs that conflict with it being the RAID controller.
 
Thanks ACCTnIT for these tips.

I feel like I'm a secret agent just handed my mission.
I, perhaps foolisly have bought one of these things (revodrive x2 240gig)
and am walking the mindfield of installing it.

I thought I would just be able to image my other SSD with the O/S on it and I'd be set but it seems a lot harder than that.

I really want to avoid a fresh install but it seems it is likely.
I am a "Hi Tech" noob so I am stumbling through it.
Thanks for the post.
 
Back
Top