HDD Freezing and dissapear with SSD + P67A-GD55

M

Maeggor

New member
PRIVATE E-2
Joined
Mar 23, 2011
Messages
3
Hello people

I have just renove my computer and bought this:

CPU                 QuadCore Intel Core i5 2500K, 3450 MHz (35 x 99)
Motherboard MSI P67A-GD55 (MS-7681)
GraphicCard NVIDIA GeForce GTX 560 Ti  (1024 MB)
Memory            G Skill F3-12800CL9-2GBXL 2 GB DDR3-1600 DDR3 SDRAM
Sound         Creative SB X-Fi XtremeMusic/Platinum Sound Card
SSD            OCZ-VERTEX2 ATA Device  (SATA-II)

I have just add also my old CorsairHX520W powersupply plus one Western Digital Green of 2TB and one Velociraptor of 300GB

The thing is that when I finish of installing Windows 7 x64 and all the drivers, when I for example use intensely the Velociraptor it freezes and finally dissapear of my computer. And then after a lot of reboot i cant initiate Windows. I am desperate. I think is related with Intel RST drivers, SATA or ACHI.

If you need to know I have install all in ACHI mode, Vertex2 in SATA0 port, Velociraptor in SATA1, and the GreenCaviar2TB in SATA3.

Any suggestions or ideas to fix it? Thanks!
 
Sort by date Sort by votes
Is it only the velociraptor drive that disappears?  Which HDD do you have windows installed on?
 
Upvote 0 Downvote
Believe the WD Velociraptor 300GB is a SATA II? How about placing it & the other WD 2TB into the SATA II ports 3 & 4 & see if that helps.
 
Upvote 0 Downvote
Yesterday I did it and it seems that works but I pass a benchmark on Vertex 2 and it lost 50MB/s in each test (read/write). It is connected on SATA III port. Now is 200MB/s in read and 200MB/s in write aprox. when before was aprox. 250/250.

Ill test Velociraptor with that drive testing software and ill tell you (by the way, where is it because I have seen WD webpage and I cant find it)

Thanks for the answers guys!
 
Upvote 0 Downvote
I just found the post whilst searching for a very similar problem with a very similar setup.

I have a MSI P67A-GD65, a Corsair 256GB P256 SSD, and a WD VelociRaptor 600GB 10k RPM.

I have been copying data from my SSD to my WD drive and the computer freezes for a period (between 20 seconds and minute) after it has copied an amount of data. Sometimes it recovers from this freeze, and other times the the drive disappears from my computer.

I have set up the drives in both IDE and AHCI mode and have the same problem with each.

Did you ever manage to fix your problems?
 
Upvote 0 Downvote
Since the OP hasn't done a followup post since April, we don't really know the outcome. No indication if he had a B2 board or a B3. It would be best if you open a fresh new thread. Please include all the systems components.

I have set up the drives in both IDE and AHCI mode and have the same problem with each.
Click to expand...
This can be further discussed in your own thread.
 
Upvote 0 Downvote
HU16E said:
Since the OP hasn't done a followup post since April, we don't really know the outcome. No indication if he had a B2 board or a B3. It would be best if you open a fresh new thread. Please include all the systems components.
This can be further discussed in your own thread.
Click to expand...

Ok.
 
Upvote 0 Downvote
Back
Top