[SOLVED] MEG Z490 Godlike Dynamic Dashboard II not working and Corsair RAM RGB not showing up in Mystic Light after MB LED FW update in Dragon Center

[Phoenix356159d02e3]

Which version of MSI Center are you running? I have a B550 Gaming Edge WiFi, which has the same family controller chip (Nuvoton NCT6687x) as the Z490 GodLike and MSI Center 1.0.40.0 offered the LED FW 0.9 update. MSI Center 1.0.41.0 has since been released as well.

I'm running 1.0.41.0

 

[HyperLAW]

Hi, I have the same issue. I tested the motherboard before case instalation and the Dashboard 2 worked fine, but after I installed all the components for mounting the computer, the dashboard 2 stopped working. I saw there was a solution for it but its not posted on this thread, can you please tell me what the solution is? Thanks

 

[Furna]

Hi, I have the same issue. I tested the motherboard before case instalation and the Dashboard 2 worked fine, but after I installed all the components for mounting the computer, the dashboard 2 stopped working. I saw there was a solution for it but its not posted on this thread, can you please tell me what the solution is? Thanks

What motherboard? The tool recovers from a failed firmware upgrade for very specific chips ... you are neither mentioning the motherboard or the firmware upgrade.

 

[HyperLAW]

Hi @Furna, sorry, the motherboard is Z490 Godlike and there was no firmware update since I haven't even instaled any windows or any software. I'm yet mouting the PC and its components.

 

[Furna]

Hi @Furna, sorry, the motherboard is Z490 Godlike and there was no firmware update since I haven't even instaled any windows or any software. I'm yet mouting the PC and its components.

That's strange ... anyway the tool runs on Windows so I would suggest you first finish the build and install Windows .. then let's see if you can "see" the controller in Mystic Light and or firmware upgrade of MSI Center ...

 

[HyperLAW]

No success. I've finished instaling my build. Instaled MSI Center and Mystic Light. Updated everything, but it's still not working. On Mystic Light the option for activate/deactivate the dashboard 2 is on (I've tried turn it off and on again), but it's still not working...

 

[Furna]

No success. I've finished instaling my build. Instaled MSI Center and Mystic Light. Updated everything, but it's still not working. On Mystic Light the option for activate/deactivate the dashboard 2 is on (I've tried turn it off and on again), but it's still not working...

Check PM

 

[HyperLAW]

Unfortunately, nothing happened I've wasted all the choices I remembered...I don't know what else to try. All the other dashboards works fine, but this one don't.

 

[Furna]

Unfortunately, nothing happened I've wasted all the choices I remembered...I don't know what else to try. All the other dashboards works fine, but this one don't.

Sorry to hear that
>>How to contact MSI.<< for RMA ...

 

[Feng]

Please check PM
Reasons to not share publicly are already explained in previous messages to this thread.
Let us know if it works for you

can I get the PM too. my display is just black and has the numbers after the LED FW Update
Board: MSI Z490 Godlike
BIOS: 7C70v1A
MB LED FW: LED_0E OLED_0D
VGA: MSI RTX3080
PSU: EVGA 750
CPU: I9 10900K
MEM: G.SKILL Trident Z 32GB (4 x 8GB) 3600mzh
OS: Windows 10 64bit
led Fw update 7C70_led

 

[Furna]

can I get the PM too. my display is just black and has the numbers after the LED FW Update
Board: MSI Z490 Godlike

Check PM

 

[tonysabo31155d02d9]

Check PM

Same issue as others posted here. Z490 Godlike...updated LED and OLED Firmware. LEDs work, but OLED is blank.

Found the MSI LED Updatetool online but I think its for the z390 version. @Furna, can you you shoot me a PM on how you resolved this? MSI only sent a generic response with how to clear CMOS, which has nothing to do with the OLED Firmware version...

 

[Furna]

Same issue as others posted here. Z490 Godlike...updated LED and OLED Firmware. LEDs work, but OLED is blank.

Found the MSI LED Updatetool online but I think its for the z390 version. @Furna, can you you shoot me a PM on how you resolved this? MSI only sent a generic response with how to clear CMOS, which has nothing to do with the OLED Firmware version...

MSI support will probably point you to the very same tool, anyway they must follow the procedure and ask you to clear CMOS at first ... anyway you have a PM.

 

[syter1154802d0]

Hello,
I have the Z490 Godlike, updated to the latest bios version anddid all the dragon center live updates.
My PCH RGB (down right part of the motherboard with the text 'Godlike') keeps 'flickering'. Anyone have an idea how to solve this? :/
(Mobo is connected with two cables from PSU)

 

[Furna]

Hello,
I have the Z490 Godlike, updated to the latest bios version anddid all the dragon center live updates.
My PCH RGB (down right part of the motherboard with the text 'Godlike') keeps 'flickering'. Anyone have an idea how to solve this? :/
(Mobo is connected with two cables from PSU)

It seems a few other users (check Reddit) fixed this issue with a firmware upgrade.
Check PM

 

[syter1154802d0]

Thx for your reply. Did not work
Guess it goes RMA.

 

[Furna]

Thx for your reply. Did not work
Guess it goes RMA.

Unfortunately I see no other option unless you can survive with that or turn off entirely every RGB led (there is a switch to turn off all motherboard LEDs)
I understand you want to have what you paid for; anyway your PC is fully functional besides the RGB.

In case >>How to contact MSI<<

 

[uniique_stiila128f02aa]

had the problem that custom gifs were stuck on upload on my z490 godlike, now it just stays black on the dynamic dashboard (oled display). can someone help?

 

[Furna]

had the problem that custom gifs were stuck on upload on my z490 godlike, now it just stays black on the dynamic dashboard (oled display). can someone help?

Check PM

 

[uniique_stiila128f02aa]

thanks, unfortunately clicking update oled i only get "send command fail"